Killing weeds is easy with contact sprays. Wherever the weed killer lands, your weeding job is nearly done. But weed killer doesn't always distinguish between valuable landscape plants, favorite flowers and the weeds you want to remove. To ensure you don't accidentally harm desirable plants with weed killer, try some of these no-miss tips.
Apply anytime - spring through fall at temperatures between 50 degrees F and 90 degrees F.
On established lawns without harming lawn grasses.
Do not use on Carpetgrass, improved varieties of St. Augustinegrass, such as floratam, dichondra or desirable clovers.
Spray when weeds are small and actively growing when temperatures are above 60 degrees and when it is sunny.
On patios, sidewalks & driveway cracks, gravel areas, paths and along fence lines. Around established ornamentals, ornamental beds, tree rings, mulched areas.
Do NOT use around non-established plants, shrubs, or trees
Spray when weeds are small and actively growing when temperatures are below 90 degrees.
Do not apply to Bermudagrass lawns when daytime temperatures exceed 85 degrees F.
On lawns without harming lawn grasses - Bermudagrass, Buffalograss, Kentucky bluegrass, ryegrass, fescue, zoysia, bentgrass.
Do not use on Bahiagrass, Carpetgrass, Centipedegrass, St. Augustine including Floratam or Dichondra.
Weed Killer Mishaps
Many spray-on weed killers are a type of post-emergent herbicide and contain the active ingredient glyphosate, which doesn't discriminate between weeds and desirable plants. This type of herbicide simply kills plants it contacts.
When this type of weed killer inadvertently drifts onto desirable plants, that's called overspray or spray drift – and it can mean the difference between killing weeds and killing a cherished plant. Sometimes, spray drift doesn't kill nearby plants, but instead produces leaf spotting, stunted growth, stems that die back or leaf drop.
To prevent problems with weed killer spray drift or overspray, follow some of these techniques.
Protect Other Plants
- Read the weed killer label. One popular weed killer label warns to avoid creating fine spray particles by using a high pressure-type nozzle sprayer, because small particles are more likely to drift.
- Spray herbicides when air is calm. If you must spray and the wind won't let up, look for a gel-type herbicide, or, if possible, paint or daub the herbicide directly on the weed.
- Use caution when spraying weeds in beds with bulbs that have died back. Many bulbs, even when dormant, react to weed killer that seeps into the neck of the bulb.
- Rinse sprayers or watering cans used to apply herbicides after each use. Dump the rinse water on a non-planted area. Don't dump rinse water on hard surfaces that will channel them into nearby planting areas or street catchment basins.
- Dedicate a sprayer or watering can for herbicide use to avoid accidentally dosing desirable plants with weed killer.
- Protect nearby plants from spray drift by covering them with plastic sheeting or cardboard. Remove the plastic after the herbicide dries.
- Avoid walking on large areas you've just treated, or you risk carrying herbicide on your shoes into other areas, like your lawn.
- Spray on cloudy days when possible. Warm, sunny conditions intensify spray drift damage symptoms.
Target the Weed
- Create a targeted spraying area by removing the top and bottom of a plastic 2-liter bottle, plastic milk jug or metal food can. Place the spray collar over the weed, and apply herbicide directly into the top opening. To spray a large weed patch, use an open-ended cardboard box to form a targeted spray zone.
- Spray one weed growing in the middle of desirable plants by cutting a small opening in a piece of plastic. Lay the plastic over the plants, and pull the weed through the opening. Spray the weed with herbicide. Remove the plastic after the herbicide has dried.
- Isolate weeds on planting bed edges by anchoring the weed to the ground with a u-shaped anchor pin. Spray the weed after you have clumped and pinned the foliage.
- Treat only the targeted weed by painting herbicide onto leaves with a sponge applicator brush. If using a bristle paint brush, take care not to flick herbicide onto nearby plants.